Friday, 19 July 2024

Outback Trip–Part 2

At the end of each day a suitable quiet bush campsite would be found and the vehicles circled around a central campfire.  For some reason food cooked over an open fire is particularly delicious.

group

The next morning we drove on exiting the Old Telegraph Track at the Balladonia Roadhouse.  After refuelling we continued east on the blacktop to the next roadhouse, Cocklebiddy.

It was here I noticed the electric vehicle recharging station powered by a generator using old cooking oil as fuel.

cocklbiddie

We left the blacktop at Cocklebiddy heading onto the unsealed Old Coach Road.  More fun driving! 

old coach road

All the recent rain meant the vehicles were starting to get very dirty.

A day later we reached Madura Roadhouse, which was another refuelling stop.

madura rh

A short drive on the Eyre Highway (blacktop) saw us reach the top of the Madura Escarpment with panoramic views of the coastal plain to the south.

madura escarpment1

This is where we left the blacktop and headed further east on the Old Eyre Highway.  The highway is the original section of east-west road across Australia.  It’s received no maintenance since the new Eyre Highway was constructed in the early 1980’s.  Interesting driving!

The geology during this part of the trip was sandstone and the route took us near many caves.  The entrances to most of them are sinkholes.

cave1cave2cave4cave5cave6cave7 

The area is popular for cave diving. 

We left the Old Eyre Highway at Eucla Roadhouse and headed down to the coast to visit the Old Telegraph Station.  This was the location where the telegrams were exchanged between South and West Australia.

Continuing east we crossed the border into South Australia.  There is a quarantine station here, however it’s operated by the West Australian State Government and only vehicles heading west are checked.  The South Australian quarantine station is further east at Ceduna.

I was carrying five 20L jerrycans of diesel on the trailer because I knew the price of fuel at the next roadhouse (Nullabor) would be the most expensive on the trip.

nullabor whale

For a small fee it’s possible to get a shower at most of the roadhouses.  Water is precious out here and filling the trailer water tank would have cost me $1 for 25 litres.

nullabor water

  nullabor1

Not much grass here! 

Two EV’s were using the charging station

nullabor solar

The old roadhouse has been retained providing an indication of what the remoteness of the highway would have been like when transiting the area 40 years ago.

nullabor old 

We left the main sealed highway continuing on the unsealed Old Eyre Highway until we again re-joined the main highway near Yalata.

The plan was to head north up Googs Track, which is just before Ceduna.  This would have avoided the South Australian quarantine station.  However some in the group needed fuel and food so we passed through the quarantine station where most people had to surrender any fruit and vegetables they still possessed.  I imagine the staff at the quarantine station eat well; and cheaply; on all the fresh food that is surrendered.

After replenishing our supplies we headed back through the quarantine station; where we weren’t stopped and searched as we were heading west; reaching the southern end of Googs Track.  This would be a test of my driving skills towing a trailer.

Monday, 15 July 2024

Four Week Off-Road Trip

In early June I joined a party of 10 vehicles on a 5000km outback trip to the northern Flinders Ranges in South Australia.  Two of us were solo drivers with the rest being couples.

The idea was to spend as little time as possible on the ‘blacktop’.   Why else be a member of a 4WD Club!

flinders

The off-road parts of the trip included:

  • Hyden – Norseman Road
  • The Old Telegraph Track
  • The Old Coach Road
  • The Old Eyre Highway
  • Googs Track
  • The Trans Australian Line
  • Andamooka Road
  • Southern Oodnadatta Track
  • Lake Eyre
  • Copley Road
  • The Great Australian Bight

The start point RV was a Brookton, approximately 140km east of Perth.

Like many of the small wheatbelt towns, Brookton has a small rural open air museum.

brookton 3brookton 4brookton1brookton2

Once the group had assembled the convoy headed further east, using various unsealed side roads to reach Hyden.  The first night was at ‘The Breakaways’ on the unsealed Hyden-Norseman road.  This was the same location where I had spent a night several months earlier on the ‘Peak Charles’ trip.

The next day we continued east to Norseman and then joined the western end of The Old Telegraph Track.   This track was originally formed during the construction of the Australian Overland Telegraph Line which was completed by the South Australian SA and Western Australian WA Governments.  The newly formed WA government committed a budget of £30,000 to the project, at a time when the state’s entire yearly revenue was about £135,000.  South Australia used steel poles whilst WA used timber (Jarrah).

All the material was carried by sea to various landing along the remote coastline.  They were then carried onwards using camels. 

One of the many problems was the South Australian Government used American Morse Code whilst the West Australian Government used the International Morse Code.  This meant that at the border telegraph station the telegraph operators sat opposite each other, with a wall between them representing the border between WA and SA. Each message had to be decoded and passed through a pigeon-hole in the border wall.

There are remnants of the line and one has to be careful when driving to avoid old pieces of wire or steel stakes that could easily puncture a tyre.

abo

Our campsite that night was adjacent to one of the old and abandoned telegraph stations gradually being reclaimed by the land.   

Sunday, 14 July 2024

Not quite there!

Well the defective drone battery recharged but the drone controller won’t accept it with screen messages informing me the battery voltage is too low and the battery is damaged.

message

More online research has revealed other people have had a similar problem.  Somewhere in the system is a memory that records the battery used to be defective and now won’t allow it to be used despite being fully charged.

My assumption is the memory function is either in the battery or the controller.  As the battery is useless in its current state I decided to fully dismantle it and inspect the battery BMS (Battery Management System) circuit board.

bms

I’s going to unsolder the Red and Black cables that the battery cells to the BMS.  If the memory is in the BMS I’m hoping removing the power to the BMS will reset the memory.   If this doesn’t work a replacement (expensive) battery will need to be purchased.

On a more positive not I’ve repaired the ebike battery charger.  Working on the principle of looking for the simple things first I dismantled the charger.

charger

Then I tested the continuity between the charger and the plug that connects to the ebike.  There was no continuity on the negative so I dismantled the plug and found the negative wire had disconnected from its terminal.

plug

A quick touch with the soldering iron and everything was good to go!.

I need to start updating the blog on my latest outback trip!

Tuesday, 9 July 2024

Faulty Drone Battery

According to the manual one of our two drone batteries has developed a fault and needs to be replaced.  The battery no longer charges and a fault is displayed by the four LEDs flashing alternately in pairs. 

faulty

These batteries are not cheap and I am loathed to purchase a replacement.  One of the things I noticed with lithium batteries is they can get confused (layman term) and aren’t really defective.  They just need to be reset.

The base and top of the battery are joined together with six small screws (one hidden) and some glue

base

After removing the six screws I used my knife to cut the glue separating the top from the base.  The two small screw securing the ribbon cable to the top were then removed allowing the top to be set to one side

opened

Pushing up from the base I was able to raise the four lithium cells and gain access to a small multi-pin plug.  The plug was secured into its socket with glue which I cut with my knife before removing the plug.  This disconnected the battery cells from the circuit board

plug

After waiting 30 seconds I inserted the plug back into the socket before plugging the battery into the charger to test if the fault had been cleared.

test

The battery appeared to no be charging correctly.

The battery was then reassembled and placed back on charge.  I noticed it was showing 75% charged and assumed one of the four cells may have contributed to the fault. 

charging

Once the battery is fully charged I’ll insert it into the drone and complete a detailed status check using the drone controller.

Sunday, 7 July 2024

Another Idea

Yesterday’s bike ride was done without a working speed gauge.  I immediately realised what had happened.  The bike stand had crushed and then cut the wires in the cable between the speed sensor on the rear wheel and the motor controller.

This is the third time it has happened and each time the end of the cable going into the motor controller gets shorter.  If this continues to reoccur I’ll need to dismantle the motor controller to replace the cable. 

The first stand I owned was attached to the frame near the rear wheel.  It wasn’t sufficiently strong to hold the bike upright when the trailer was attached.  Luckily it snapped on the last day of my first trip to Taiwan.

The second stand has two legs and fits immediately behind the centre hub.  The issue is this is also where the cables from the motor exit and the stand tends to catch on the cables.

old stand

Arrow points to the cable pinch point

Another solution was required.   Initially I thought I’d just prop the bike against a tree, wall or fence.  However that only works if one is available.   Google had a photo of a purpose made bike stand designed for laden touring bikes.   However it would need to be purchased from the USA and was expensive.  I decided to try and make one. 

My idea involved purchasing a cheap extendable trekking pole from the local KMart ($9.50)

stick

The handle and strap were removed and replaced with a small wooden block and a half section of surplus pvc pipe.

mod

Two small button bungees are used to apply the bike brakes.  This prevents the bike from moving away from the stand.

bungee

A third bungee is used to secure the new stand to the bike frame.

new stand

The idea seems to work, but I’ll need to conduct a few trials to confirm that.

When stored the pole is collapsed and secured to the top bar of the frame using the bungee cords.

stored

It’s obviously not as quick to use as an attached stand.  But I’ll only need to use it when there is no readily available tree, wall or fence!

Saturday, 6 July 2024

Voyage to Tonga

The 2024 long outback trip has been completed and the clean-up has commenced.  There is a considerable amount of cleaning to be completed and I won’t start writing about the trip until that has been done.

Meanwhile our eldest grandson has departed Opua, NZ for the capital of Tonga, Nuku'alofa, on his steel ketch, SB Cowrie accompanied by his girlfriend and a 3rd crew member.  Cowrie was built in Cornwall, UK in 1991 and sailed to NZ via the Falkland Is and Cape Horn.

cowrie

They are using the “blackbox” navigation system I assembled using a Raspberry Pi4 and I’ve been slightly worried about the reliability of the system.

He sent us a link to MapShare which allows us to monitor their course.  A couple of screen dumps are attached below.

course

It appears after 10 days at sea they have reached Minerva Reefs anchoring inside North Minera Reef.

minerva reef

The reefs only appears above the waterline at low tide and is a well used resting point for yachts heading to Fiji or Tonga.  The north reef also provides a relatively safe anchorage during bad weather.

I’d better get back to cleaning.   More to follow!

Thursday, 6 June 2024

Huff & Puff

Obviously I’m not getting any younger.  Since resuming cycling three years ago I’ve managed to break two hand operate bicycle tyre pumps.  It’s probably a combination of cheap pumps and excessive force, likely due to exhaustion! 

Interestingly, since purchasing the first pump I’ve not experienced a puncture whilst riding.  However I’ve needed to reinflate tubes after replacing worn tyres and the airline has required the tyres to be deflated for transport.

A number of years ago an Australian company invented the first small battery operated bicycle pump.  They then made the usual mistake of having it manufactured in China.  The pump was a success and it didn’t take long for their concept to be copied. 

One potential issue with the original design (and a number of clones) was the lack of an inbuilt air pressure gauge.  To check the required pressure had been achiever the pump needed to be disconnect and a separate gauge used.

Finally a Chinese manufacturer has produced a derivative of the pump with a display and at a price I’m prepared to pay.

It was delivered today. 

pump1

It was well packaged and upon opening the box the first thing I noticed was the comprehensive manual; a Quick Guide and the pump in a silicon case

Untitled-1

Underneath the pump were several valve attachments and a USB-c charging cable.

P1030858

A – Presta hose

B – soft spacer

C – Needle attachment for ball inflation

D – Schrader Valve Attachment

E – Presta attachment

Both our bikes have Presta valves.  I could therefore use either A or E.  I’ve opted for A

P1030859

When turned on the display shows the tube pressure, battery state and the pump mode.  The modes are Bicycle, Motorbike and Ball.

The functions of three buttons below the screen are:

Left – Increase pressure in increments of 0.5psi

Centre – On/Off and change mode

Right – Decrease pressure in increments of 0.5psi

The default pressure setting is 45psi

The pump will operate continuously for 2.5 minutes before automatically turning off.  It can’t be reused for 8 minutes.  This enables the pump to cool.  2.5 minutes should be enough time for me to reinflate at least two tyres.  Well I only have two!! Smile

The specifications state recharging time is less than 1.5 hours.

I have three options when it comes to a recharging source. 

  1. Use a mains powered USB charger
  2. Use one of my portable power banks
  3. Use the USB socket on the Bafang motor battery

The final step in this project was to identify a suitable location to carry the pump on the bike.  The handlebar bag was the most obvious location.  Eventually I opted to secure it under the saddle and save some space in the bag.  Hopefully it won’t need to be used and will just be one of those items you wish you had when you need one!

seat-1

Saturday, 1 June 2024

Stupid Welsh

Not the people of Wales.  It’s the daffodils!  The idiots haven’t realised it’s only the last day of autumn and they are already more than a foot out of the ground!

daffodils

The rain bucketed down last night (well rained heavily for Perth).  Jan heard hail during the night and the morning TV news showed 10cm thick hail in the south of the city.  What a novelty!  We didn’t experience any damage, however my brother had his outdoor table glass top blown off.  He was cleaning up the mess when I phoned to enquire if he was OK.

I’m scheduled to depart on another long outback trip in eight days and am hoping the rain hasn’t turned the route into a quagmire.

Whoever installed the original pantry power socket needs a good kick at the bottom end of their elementary canal.  The cut-out in the block wall is too big for the plastic box.  I decided to attempt to secure the box with the last of the splashback adhesive.  If that doesn’t work I’ll probably have to make some type of mounting plate and fit it into the cavity. 

socket

A problem with the bicycle gears may have been identified and solved.

For several weeks the Shimano Alfine 11 speed rear hub has been intermittently missing gears.  Everything is fine from gears 1 to 7 but 8 to 11 are frequently missing,  The pedals just spin!  Sometimes I can engage a gear after a ‘clunk’ or grinding sound.

The wheels was removed and the hub disassembled before being placed in the ultrasonic cleaner.  During reassembly the bearings were greased and new oil added.  It didn’t solve the problem! 

Next I bought a new gear cable in the hope the original one was defective.  That didn’t work either!

I tried adjusting the gear cable using the adjuster screw (this is called ‘Indexing’).  Tightening the cable gave me gears 8 to 11 but I list gears 2,3,4,&5.  My concern was something had broken inside the hub.  That would be very expensive.

Looking for the simple thing first (and the cheapest) I decided to replace the sheath through which the gear cable runs.  Much of the sheath is inside the frame of the bike.

That was when I discovered a potential cause of my issue.  Where the sheath exits the upper part of the bike frame it was kinked and crushed.

cableport

Enters the frame though this hole.

kink     

Kinked and crushed.

I replaced both the sheath and gear cable before adjusting the gears.  During this operation a second issue was identified.  where the sheath exits the bottom of the frame it crossed over the hydraulic line to the rear brake.  This was also compressing the sheath.  Re-routing the sheath solved this.

On reflection the issues were created by two separate activities.   The kink and crushing of the sheath was likely caused by me when I raised the height of the handlebars by adding a stem extension.  This shortened the length of the sheath creating a pinch point when the handlebars turned fully to the right.   The second problem was likely caused by the Taiwanese bike mechanics in Hualien.  They replaced the hydraulic brake lines and probably didn’t realised they had crossed the gear cable sheath.

I need some fine weather to do a test ride and confirm all the gears have been restored.